778865 SLIP COAT PLUS 25 LTR

Product information

This product supersedes product no: 757395

Specification

Approvals

• This composition meets the criteria for not being harmful to the marine environment according to MARPOL Annex V and may be discharged into the sea when used to clean cargo holds and external surfaces on ships.

Directions for use

To achieve optimal protection the cargo hold surfaces should be as clean and dry as possible before treatment with Unitor™ Slip Coat Plus™. NOTE! After cleaning with sea water, holds should always be flushed with fresh water before applying Unitor™ Slip Coat Plus™. The ready-to use concentration makes it ideal for application directly from the Chemical Applicator by use of the Unitor™ Panamax Cargo Hold Cleaning Kit™ and correct application nozzle.

Do not apply more than necessary, one single application is sufficient and will cover 10--20 m2/ltr depending on the condition of the cargo holds. Start applying Unitor™ Slip Coat Plus™ from top and downwards. Allow the film to dry completely before loading the cargo a process which takes 1-2 hours depending on air and surface temperature and humidity.

Note that larger amounts of Unitor™ Slip Coat Plus™ may end up at tank top when holds are sprayed. Ensure that only a thin layer is applied on the tank top. Avoid larger amount of Unitor™ Slip Coat Plus™ and remove excessive remaining for optimal result. For removal of excessive Unitor™ Slip Coat Plus™ on tank top it is recommended to use the Unitor™ VCAD 200 (682054). Flushing away excessive amounts of Unitor™ Slip Coat Plus™ with fresh water is also possible before drying.

After drying, Unitor™ Slip Coat Plus™ creates a dense, non-sticky film on the cargo hold surfaces. After cargo discharge, both the film and cargo residues are easily removed by the use of an alkaline cleaner like Unitor™ Aquatuff™ or Unitor™ Aquatuff High Foam™. A minimum 10 % solution in fresh water is recommended, leave for 15-30 minutes, re-soak with Unitor™ Aquatuff High Foam™ to keep surface wet during soaking (avoid surface to dry), and finally flush with clean high pressure water. After flushing with water, let the surfaces dry and then repeat the treatment with applying Unitor™ Slip Coat Plus™ before the next cargo.

Note! The lowest surface temperature when applying Unitor™ Slip Coat Plus™ is +5 Celsius

Note! Maximum temperature for surfaces and cargo should not exceed +70 Celsius

Always follow paint manufacturer recommendations and always allow paint to cure before applying cargo or chemicals.

產品特點

• 防水貨艙屏障

• 即買即用- 一個單一的應用程序

• 所有塗料都完全安全

• 可使用堿性清潔劑輕鬆移除

• 水溶性- 不含烴類溶劑

• 基於FDA列出的成分的組合物

優勢

• 對所有表麵都有出色的附著

• 適用於潮濕和腐蝕性貨物 ，如硫磺 ，鹽等 。

• 防止最難清洗的貨物也能粘附在塗層上

• 節省清潔時間和清潔化學品

• 提供臨時防腐蝕保護

訂購信息

Product Number             Product name

778865                    SLIP COAT PLUS 25 LTR

認證

• 根據MARPOL附則V ，該組合物符合不對海洋環境有害的標準 ，並且當用於清潔貨艙和船舶外表麵時可以排入海中 。

使用說明

為了獲得最佳保護 ，在使用Unitor™Slip Coat Plus™處理之前 ，貨艙表麵應盡可能幹淨和幹燥 。注意 ！在使用海水清潔後 ，在使用Unitor™Slip Coat Plus™之前 ，應始終用清水衝洗 。即用型濃縮液使其成為直接應用於化學品的理想選擇

塗抹使用Unitor™ Panamax Cargo Hold Cleaning Kit™和正確的噴嘴.

D不要超過必要的應用量 ，一次單獨的應用就足夠了 ，根據貨艙的狀況將覆蓋10-20平方米/升 。從頂部和向下開始使用Unitor™Slip Coat Plus™ 。在裝載貨物之前 ，讓薄膜完全幹燥 ，這需要1-2小時 ，具體取決於空氣和表麵溫度和濕度 。

請注意 ，噴塗固定裝置時 ，較大量的Unitor™Slip CoatPlus™可能會最終落在罐頂 。確保在罐頂上僅塗抹薄層 。避免使用大量Unitor™Slip Coat Plus™並去除過量殘留物以獲得最佳效果 。為了去除罐頂上過多的Unitor™SlipCoat Plus™ ，建議使用Unitor™VCAD 200（682054） 。

在幹燥之前 ，也可以用淡水衝洗掉過量的Unitor™Slip Coat Plus™

幹燥後 ，Unitor™Slip Coat Plus™在貨艙表麵形成致密 ，不粘的薄膜 。貨物卸貨後 ，通過使用堿性清潔劑（如Unitor™Aquatuff™或Unitor™Aquatuff High Foam™）可輕鬆去除薄膜和貨物殘留物 。建議使用至少10％的淡水

溶液 ，保持15-30分鍾 ，使用Unitor™Aquatuff High Foam™重新浸泡 ，以在浸泡過程中保持表麵濕潤（避免表麵幹燥） ，最後用幹淨的高溫衝洗壓力水 。用水衝洗後 ，讓表麵幹燥 ，然後在下一批貨物之前使用Unitor™Slip Coat Plus™重複處理 。

注意 ！使用Unitor™Slip Coat Plus™時 ，最低表麵溫度為+5攝氏度

注意 ！表麵和貨物的最高溫度不應超過+70攝氏度始終遵循塗料製造商的建議

並且在使用貨物或化學品之前始終確保油漆固化 。