產品中心 Products Center
575696 CARBONCLEAN LT 25 LTR
Product information
Unitor™ Carbonclean LT™ contains no chlorinated solvents or phenolic compounds and has low toxicity to the environment and to persons handling it.
It is developed and ideal for removing carbon type deposits from heat exchange, burner tips, fuel injectors, and other engine parts being contaminated by carbon residues.
Features
- Reformulated with improved cleaning properties
-
Can be used for cleaning engine parts including, but not limited to:
- Pistons
- Piston rings
- Valves
- Valve cages
- Does not contain nonylphenol ethoxylates or other estrogenic compounds
- Simple and economical to use by soaking or circulation method
- Low toxicity and evaporation rate
- No phenolic or chlorinated compounds
- Cleans oil side of fuel and lube-oil heaters, oil coolers, etc.
- Removes carbon based deposits from fuel and lube oil filters
Benefits
- Non-corrosive, safe on all light metals, including aluminium
- Quickly dissolves deposits containing carbon, resins or varnishes
- Eliminates need for hard scraping
- Effectivly removes carbon type deposits from burner tips, fuel injectors and all components fouled by carbon, resin or varnishes
Specification
General
Invent Hazard Material (IMO/EU) classification | C-49 |
---|
Physical properties
Appearance | Pale yellow |
---|---|
Density [g/ml] | 1,0 |
Flash Point [°C] | Above 61 |
Form | Liquid |
Technical data
Not Compatible | May swell rubber and synthetic rubber. |
---|
Directions for use
Soaked method
This method is an effective way of cleaning deposits from machine parts. The items to be cleaned are dipped into the cleaning solution. A wire basket can be used for small components. For removal of light deposits or oil, a dilution of up to 1:2 in fresh water can be used. Light deposits will be removed in 1 hour, whereas heavily oxidised deposits may need overnight soaking. After the components have been removed from the soaking bath, remaining cleaning solution is easily flushed off with water.
Due to a very low evaporation rate, no precautions are necessary to prevent loss of liquid, but adequate ventilation is recommended.
Cleaning the Oil Side of Heat Exchangers Where in-site cleaning is required, Unitor™ Carbonclean LT™ can be used neat and circulated through the unit in question. Time required for this process will again depend on extent of fouling and may take up to 24 hours.
The Unitor™ Chemical Cleaning Unit - Product no. 737189 - is recommended to be used.
- Disconnect the heat exchanger's oil inlet and outlet, drain off any remaining oil.
- Connect the discharge side of the Chemical Cleaning Unit (CCU) to the lower heat exchanger connection and fit the return to the CCU.
- Add Unitor™ Carbonclean LT™ to the drum, Unitor™ Carbolcean LT™ can be diluted to 25% with fresh water, and heat, maintaining the temperature (max 60°C), throughout the cleaning operation. If heat is not available the cleaning time will need to be extended and a higher product concentration is beneficial.
- Circulate for 12 hours. When the cleaning is complete, disconnect the lower heat exchange connection and drain out the cleaning solution.
- Connect a fresh water supply to the upper heat exchanger connection. Rinse until water runs clear.
- Disconnect the water supply, drain and dry the heat exchanger.
The Unitor™ Chemical Cleaning Unit can also be used for cleaning by soaking or circulation. Results can be achieved with maximum efficiency and with the minimum use of Unitor™ Carbonclean LT™.
產品特性
• 改良後的清潔性能
• 可用於清潔發動機部件 ,包括但不限於 :
• 活塞
• 活塞環
• 閥
• 閥殼
• 不含壬基酚乙氧基化物或其他雌激素化合物
• 通過浸泡或循環方法使用簡單且經濟
• 低毒性和蒸發率
• 無酚類或氯化物
• 清潔燃油側麵和潤滑油加熱器 ,油冷卻器等 。
• 去除燃油和潤滑油過濾器中的碳基沉積物
優勢
• 對所有輕金屬(包括鋁)均無腐蝕性 ,安全
• 快速溶解含碳 ,樹脂或清漆的沉積物
• 無需進行硬刮
• 有效去除燃燒器尖端 ,燃油噴射器和碳 ,樹脂或清漆汙染的所有組件中的碳類沉積物
訂購信息
Product number Product name
575696 CARBONCLEAN LT 25 LTR
使用說明
浸泡的方法
該方法是清除機器零件沉積物的有效方法 。將要清潔的物品浸入清潔溶液中 。金屬絲籃可用於小型部件 。為了去除輕質沉積物或油 ,可以使用淡水中最多1 :2的稀釋液 。輕度沉積物將在1小時內被除去 ,而高度氧化的沉積物可能需要在一夜之間浸泡 。從浸泡浴中取出組分後 ,很容易用水衝洗掉剩餘的清潔溶液 。
由於蒸發率非常低 ,因此無需采取任何預防措施來防止液體流失 ,但建議進行充分的通風 。.
清潔換熱器的油側如果需要進行原位清潔 ,Unitor™ Carbonclean LT™可以整齊地使用並通過相關裝置循環 。此過程所需的時間將再次取決於結垢程度 ,可能需要長達24小時。
建議使用Unitor™ Chemical Cleaning Unit - Product no. 664613807
1. 斷開熱交換器的進油口和出油口 ,排出剩餘的油 。
2. 將化學清洗單元(CCU)的排放側連接到下部熱交換器連接 ,並將返回裝置安裝到CCU 。
3. 將Unitor™Carbonclean LT™添加到轉鼓中 ,Unitor ™Carbolcean LT™可用淡水稀釋至25% ,並在整個清潔操作過程中加熱 ,保持溫度(最高60°C) 。如果沒有熱量 ,則需要延長清潔時間 ,並且更高的產品濃度是有益的 。
4. 循環12小時 。清潔完成後 ,斷開下部熱交換連接並排出清潔溶液 。
5. 將淡水供應連接到上部熱交換器連接 。衝洗直至水流清澈 。
6. 斷開供水 ,排幹並幹燥熱交換器 。
The Unitor™Chemical cleaning unit也可用於浸泡或循環清洗 。
結果可以通過最大效率和最少使用Unitor™ Carbonclean LT™來實現 。
版權所有 :江蘇亞美國際貿易有限公司 備案號 :蘇ICP備17042192號-1 網站建設 :